Tisas Regent (Browning Stainless Steel Hi-Power Clone)

Oct 23, 2007
68
1
8
66
Glendale, Arizona
#1
I've been reading nothing but good about this pistol since it came out. Brownell's has them in stock in both black, as well as Stainless Steel. It's not hard Chrome plated like the FN Browning's, but rather a full Stainless Steel pistol. As you know Browning has discontinued the Hi-Power. So this Turkish clone by Tisas is the only one of it's kind in current production in Stainless Steel. (They also offer a model in black Cerakote for slightly less).

https://www.brownells.com/firearms/...s|Cartridge_1=APP_9+mm+Luger&avs|Make_3=Tisas

It arrived last week at my FFL, and I immediately drove over to pick it up. This is a beautiful gun! Especially for it's modest price of only $569.00. (Brownell's charged a $10.00 handling fee, and my FFL charged $30.00 for the transfer). So the grand total was $609.00 to get it from Brownell's to my kitchen table. Not too bad for a Stainless Steel Hi-Power.

Overall I'm very impressed. The machining and workmanship is impeccable. Very few tool marks on the inside of the slide and frame, and a nice slide to frame fit. The overall fit and finish on the pistol is beautiful! The gun field stripped very easily. It comes with 2, 13 round, polished blue Mec-Gar magazines. They interchanged with all of the other magazines I have for my other 2 Hi-Powers.

I gave everything a good cleaning and oiling. Except for the slide rails, which I greased with Weapon Shield Lithium Grease. It went back together without a hitch. I'm hoping to get it out to the range next week, assuming everything dries out. (It's been raining cats and dogs here for the last several days).

I ordered the Tisas BR9 Hi-Power Essential Reliability Kit from BH Springs Solutions. It gives you an extra extractor, and firing pin face plate. The kit also contains new springs and various roll pins required for installation. It's a good kit with quality parts that's nice to have on hand. I intend to shoot the hell out of this thing, so having a few extra parts for it in stock can't hurt. They could also come in handy for my other 2 Hi-Powers, should any small parts go south. Some of the very early production models of these guns had some issues with extractor breakage. But those were supposedly corrected, and these newer models are good to go.

https://bhspringsolutions.com/tisas-br9-hi-power-/358-tisas-br9-hi-power-essential-kit.html

If any of you guys are wanting a Hi-Power, but waited too long, and don't want to pay the high prices being asked for the used one's, don't be afraid to grab one of these. Quite honestly, for the price, I just don't see how you can go wrong. If this thing shoots half as good as it looks, I'll be a happy camper. Here are a few quick and dirty phone pics.



 
Likes: steve123
Oct 23, 2007
68
1
8
66
Glendale, Arizona
#2
Tisas Regent Range Report, (400 Rounds)

I got to the range early yesterday with the new Stainless Tisas Regent, and gave it a good workout with a total of 400 rounds of various ammunition fed through no less than 6 different magazines. I am happy to report the pistol performed flawlessly. Not a single FTF or FTE, or any type of hiccup of any kind!

Needless to say I was extremely pleased. The 6 magazines that were used were as follows. 2 original Browning Phosphate coated 13 round magazines, with the, "springy thingy" at the bottom, to assist in kicking the magazine clear of the gun. 2 gloss blued 13 round Mec-Gar magazines that were shipped with the pistol. And 2 gloss blued 15 round Mec-Gar magazines that were new in the box.

The magazines were all filled to capacity, and all fed flawlessly in the pistol, regardless of the type of ammunition they contained. With the exception of the Phosphate coated Browning magazines with the spring assist, they did not drop free when released. But all were very easily removed from the pistol when empty. All 6 magazines locked the slide back when the last round was fired.

The ammunition used was as follows. 100 rounds of CCI 115 gr. FMJ Blazer Brass. 100 rounds of Remington brown boxed 115 grain law enforcement training ammunition. (This ammo was the hottest 115 gr. FMJ Ball I've ever shot). 100 rounds of Federal 124 gr. FMJ. And finally 100 rounds of Federal 115 gr. 9BPLE +P+ Hollow Points.

All 400 rounds cycled the pistol perfectly. 4 magazines, (2, 13 round Browning's, and 2, 13 round Mec-Gar's), were shot rapid fire as fast as the trigger could be pulled. "Mag dumps", if you will. This was with the Federal 9BPLE, and was done to test rapid fire functioning with high performance ammunition. All 4 magazines fed perfectly. The brass was ejected cleanly and about 6 to 7 feet to the right, and 3 feet to the rear, in a nice neat 3 to 4 foot circle. I examined the cases as I gathered them and returned them to the box, and none showed any signs if denting or damage. I would call the extractor on this gun perfect. No problems with it what so ever.

All shooting was done at 25 yards. The sights were adjusted perfectly, printing dead center with a 6 O'clock hold. The gun was warm, but was allowed a substantial amount of time to cool as all 6 magazines were reloaded. The trigger was slightly gritty for the first 100 rounds or so. But it smoothed out nicely as the shooting progressed. And after the last box of ammo went through the gun, it was breaking cleanly and very crisp after a minimum amount of predictable take up.

Overall I couldn't be more pleased with this pistol. It ran with 100% reliability for 400 rounds. With a good variety of different types of 9 MM ammunition. As you can tell from the picture, the gun got quite filthy after 400 rounds. But after a field stripping, and a good cleaning in Kerosene, followed by a good blow drying and re lubrication, it was as clean as when removed from the box.

I'm going to pick up another one of these pistols. I just don't think for the price you can beat them. They are well made, reliable, accurate, and very nice looking pistols. And with Browning ending Hi-Power production, these are as nice of a clone as you're likely to come across.

[img ]
 
Apr 17, 2010
872
100
43
71
Astoria, Or.
#3
Could you be specific about accuracy. Group sizes and are you shooting unsupported or from a rest or sandbags etc? Have you seen a difference in accuracy between 115s and 124s? Has there been any conclusion to the failures in parts and the misaligned chambers? Is the importer or manufacturer correcting these problems? A stainless clone is very interesting.
 
Oct 23, 2007
68
1
8
66
Glendale, Arizona
#4
Could you be specific about accuracy. Group sizes and are you shooting unsupported or from a rest or sandbags etc? Have you seen a difference in accuracy between 115s and 124s? Has there been any conclusion to the failures in parts and the misaligned chambers? Is the importer or manufacturer correcting these problems? A stainless clone is very interesting.
I shot off a supported rest, (padded wood), at 25 yards. I would say groups were averaging around 4" at that distance. Some went a little tighter, some a little worse. Wind was calm and not a factor. I could tell little if any difference between accuracy of the 115 and 124 grain slugs. Except the heavier bullets printed about an inch or so higher. The Federal 115 gr. 9BPLE +P+ Hollow Points seemed to print the tightest for some reason. Which I thought was surprising because they were the worst in my CZ-75's. Both the Standard and P-01 Shadow.

The off center bored chamber issues, and extractor breakage problems were limited to the first 400 guns or so. My gun was #1,459. The chamber on my barrel is centered to within .001, and the extractor has presented zero issues thus far. Most everyone I've talked to with a 4 digit gun has had no problems with them. And the people who have had problems with the early guns, have had them successfully resolved in a timely fashion from LKCI.

I'll send some more downrange with it next week. But I'm not expecting any issues. If the extractor should go, I'll replace it with the FN extractor from the BH Spring Solutions Kit. It's an easy change out. But for now I have no intentions of fixing what isn't broken.