No not at all. There's quite a bit more machining actually. Are you looking for a bunch of designs carved into it? It looks wonderful. K.I.S.S.has anyone else noted the serious lack of machining and block like contour compared to the AXMC around the folding butt and elsewhere to be honest.
I’m not sure about the IMUNS mount but the factory NV bridge aligns with the tall optic rail. It will also protrude past the chassis about the same length as your SamB spigot.Question for the masses. I have an AT with the higher optic rail and an mpa 1.5" mount. I'm looking at a few options to attach my pvs30 to it, will the badger imuns be inline with the scope rail or will I have to go with the nv bridge that AI makes? The rifle in question:
I had a double take moment recognising that range and yourself. I'm one of the other AI users out there.
My bad, AXSR brother. I'm still waiting to finger f..k the new TBAC stuff first.
I received a response and AO can export to Aus mate, but after setting up the rifle, unsure whether I need the cheek piece yet. I'll be moving states this year so will convert this to a folder and grab that thumbrest though, I definitely think that will be of benefit. AO has some great things on that site, had to stop myself going down the rabbit hole.@Simia Dei hmm...I wasn’t aware Anarchy couldn’t export to Australia. Did you contact them through the website?
The PVA only goes up to 30 cal? I think I'll be swapping the brake out on this one sooner than later. I'll give this a run and see if I can get hands on a comp trigger.I've owned every brake made by PVA and they are amazing. The recoil reduction is obviously most important and it does a great job but what else is awesome is the lack of concussion from the blast. I've used other brakes and after a day of shooting, I could feel the effects of the concussion in my head and sinuses. I dont get that from PVA brakes, especially the Jet4 brake. YMMV but I'm sold on them. Anarchy outdoors carried the thumb rests and check pieces from AO and I'd bet they can export. The comp trigger is awesome. I love it. It was worth the money. As long as you dont get rid of the 1st stage and make it a single stage trigger (which you can), u shouldn't have any reliability issues at all
Nice idea! I've been storing the Allen key like this for a while.Had this rifle for 6 years and still learning things about it. Of course right at the time I’m trying to sell it. For you guys with pre-14’s or AT’s, this is a perfect spot to store the Allen wrench used by most scope turrets. Give it a try.
View attachment 7229940
View attachment 7229948
Here is your 308 bolt body buddy.Picked this up yesterday, same comments I'm sure as everyone else made when they bought their first AI. Definitely wasted too much time and money on customs guns. Should have just grabbed one of these, the bolt lift is lighter and smoother than my tempests. Unsure whether I send this off for a lick of paint yet or if I'm going to swap this barrel for a 28" 338LM carbon instead. I will definitely be grabbing a .308 boltface when one pops up and will keep my ears to the ground for short action ASR mags hitting our shores.
View attachment 7233074
Apologies for the delay in replying below fellas, juggling a few things this week, and children. And their flailing arms makes it more so challenging to juggle, especially my eldest.
I received a response and AO can export to Aus mate, but after setting up the rifle, unsure whether I need the cheek piece yet. I'll be moving states this year so will convert this to a folder and grab that thumbrest though, I definitely think that will be of benefit. AO has some great things on that site, had to stop myself going down the rabbit hole.
The PVA only goes up to 30 cal? I think I'll be swapping the brake out on this one sooner than later. I'll give this a run and see if I can get hands on a comp trigger.
Are there any Rem 700 triggers out yet that come close to the AI trigger?
They certainly do... color coordinated for your stock... I believe the largest is 1/2 “... you’ll need longer screws to thread through... all factory / OEM spec’d. Good luck!Just installed the AX conversion on the AT. LOP is a bit short, even maxed out. Please tell me they make spaces for the AX Buttstock
just use the black buttstock and spacer(s) from your original stock. That’s what I did.Just installed the AX conversion on the AT. LOP is a bit short, even maxed out. Please tell me they make spaces for the AX Buttstock